This handy gadget is a travelling inkwell, introduced in 2018 by Italian company Pineider. A friend arranged a group buy for our London UK Fountain Pen Club although they are now available from Cult Pens at £20.00.
What’s in the box.
The pen filler comes in a simple cardboard box, about the size of a cigarette packet. One side of the box has two holes, one of 9.5mm, one of 13.5.mm diameter, being the minimum and maximum size grip sections that can be used. The idea is to use these holes to check that your pen is neither smaller than the small hole, nor larger than the large hole.
Inside the box, was the pen filler together with a small pipette or eye-dropper (although I am not sure these are always included) plus a sheet of instructions. If no pipette is included, use your own or a syringe to fill the pen filler.
The pen filler is comprised of four parts: the clear plastic ink holder with a measuring scale in 1ml units, up to 10ml (or 10 cubic centilitres), a black plastic knurled collar and a black plastic stopper. Hidden by the collar is a blue rubbery sleeve, part of which fits into the ink holder.
How to use.
Preparation: It is recommended that you first check that your pen is not too big or small for the pen filler, using the holes in the box if in doubt. Next practice with water first. Fill the ink holder with water, up to the 10cc mark. If you have a number of pens that you might wish to use with the pen filler, then it might be convenient to flush them all and try each of them in turn with the filler and make a note of which pens you have tried. According to the instructions, “you can use the pen filler to fill lever pens, piston pens, plunger pens, converter pens and even the old eyedropper pens.”
Filling the pen: It is recommended that the pen be emptied first. If it had last been filled with the same ink, you could discharge it into the pen filler if you are not too fussy about only using fresh ink. If using a converter or piston fill pen, then wind the plunger down first, before locking the pen into the pen filler. This is to avoid over-pressurising the ink holder and causing leaks.
So, you are ready to fill your pen.
- remove barrel of pen (if using a converter) and wind down the plunger;
- pull out the stopper from the pen filler; unscrew the knurled black collar (which gradually increases the opening) until you can insert your pen;
- tighten the collar; (as you screw the collar down, the blue rubber sleeve tightens around the grip section of the pen); continue until the pen is held firmly. This stage is a little awkward as you are holding the pen in one hand with the barrel removed and so take care not to dislodge the converter from the pen);
- Now the fun/risky part. Turn the bottle upside down, allowing the ink to cover the nib. Wind the converter or operate the piston to fill the pen, by a combination of suction and gravity;
- Once filled; turn the pen and bottle the right way up again; unscrew the collar a little until the pen comes free; remove pen; screw the collar back down fully and insert stopper.
- Replace the barrel on your pen, wipe off any ink from the section and nib. And you are ready to go.
There are some limitations to the use of the pen filler, for those pens which are too wide or too narrow for it. For oversized pens you may have to fill these direct from a bottle. For pens too narrow to use the pen filler system, you may still be able to fill from the travelling ink well, just by removing the stopper and dipping the pen into the ink (if the ink level is deep enough).
- The pen filler is a very convenient size for travelling, being small and light weight, when you do not want to travel with a typical 50ml glass bottle.
- A 10ml supply of ink is enough to fill a typical converter around 12 – 15 times I found, although I confess that I lost count while attempting this exercise, filling a pen repeatedly with water until empty.
- If used correctly and carefully, it is possible to get a good fill with minimum inky mess.
- You can still fill a pen even from your last 1ml of ink! This would be difficult for most pens, if filling from a conventional bottle.
- You do not need to be too anxious about the pen not being perfectly clean from a previous ink, as you will not contaminate a whole bottle, but only a few millilitres.
- You can experiment by mixing compatible inks, just a millilitre or two at a time, in your pen filler. (I made a blend of Robert Oster Aqua and Pilot Iroshizuku Shin-kai, about 50/50, although this carries some risk that certain inks will not be compatible and will combine to make a sticky goo). It is prudent to test out any such blends in a separate receptacle and leave to stand for a day or so, before filling your pen.
- If going away for a few days, it can be very handy to have a little supply of ink with you just in case you buy a pen (!), or as happened to me recently while visiting an elderly aunt over the holidays, I was asked to see if I could get her old Parker Slimfold working again and she could not find any ink in the house. In this situation it is little consolation to know that you have an entire drawer-full of fountain pen inks back at base camp.
I am impressed with the simplicity of the design. If used correctly and with care, it works well. It is not entirely fool proof and it is a good idea to practice first with any given pen, using water until confident. When I first got mine, I picked a fairly large sized cartridge converter pen and was interested to see how many times it could be filled, from 10ml of water and using even the last drop. I have been using it successfully for a few weeks now. However, in trying it last night newly filled with Conway Stewart Tavy to photograph for this post, I must have done something wrong and ink leaked over my hands. This could be due to me forgetting to wind down the plunger prior to locking the pen into the holder, or not tightening the screw-down collar sufficiently before inverting the bottle, or perhaps dislodging the converter slightly. Like I said, it is not fool proof.
As for durability, it remains to be seen whether the plastic ink holder may crack eventually from the repeated stress of tightening and loosening the collar but I would expect it to last for a few years at least and would be happy with this. As for value, when looking at the four individual components of the pen filler, each of which looks mass-produced costing only a few pence each, it is questionable whether the sum of the parts amounts to £20.00. I sometimes feel like this when looking at the disassembled parts of a fountain pen. Obviously the company needs to make a profit and the initial costs of designing the parts and manufacturing them all need to be taken into account.
Overall, for the usefulness of the pen filler I would be happy to spend £20.00. And for the question of what to give a fountain pen enthusiast, who has everything except a Pineider Pen Filler, this is a good answer.